MRS SYSTEMS GUIDE
coming soon
XF CONSTRUCTION GUIDE
DOWNLOAD
REQUEST SAMPLES HERE
ONLINE ENQUIRY
HERE
  • MonoTherm TXF
  • Colours
  • Finish
  • Technical Download

MonoTherm TXF is a flexible insulated render system manufactured for installation onto EPS, ICF and mineral wool insulation, render carrier boards in conjunction with timber and steel frame and direct onto most masonry.

The through coloured TXF Acrylic finish is installed to achieve a lightly textured decorative finish.

Insulated system

The comprehensive MonoTherm TXF insulated system is designed specifically for each project based on the type of construction and which type of insulated component best suits the particular substrate.

The thickness of the insulated component (EPS, ICF or Mineral Wool) is then specified so that the combined thermal performance of the through the wall materials meet building regulations or a particular thermal value.

The chosen insulated element is bonded to masonry using MonoFlexBase TXF base coat and system specific mechanical fixings.

MonoFlexBase TXF is also applied as a base coat in preparation for TXF Primer and the TXF Acrylic finish layer.

MonoMesh TXF is imbedded into the entire MonoFlexBase TXF layer whilst wet.

Mesh beads are installed to encapsulate the base coats and give definition to the finished product.

The following build up detail shows a typical MonoTherm TXF insulated system onto masonry and is provided as guidance only.

Build up guidance

MonoFlexBase TXF is installed over masonry to bond insulation
The specific size of insulation is bonded and mechanically fixed to masonry
MonoFlexBase TXF is installed over insulation
MonoMesh TXF is imbedded within MonoFlexBase TXF layer
TXF Primer is applied over MonoFlexBase TXF when dry
TXF Acrylic is applied to finish

MATERIAL COVERAGE GUIDANCE

MonoFlexBase TXF 25kg bag 2.5m2 - 3m2 Bonding of insulated substrate
MonoFlexBase TXF 25kg bag 2.5m2 - 3m2 Base coating over insulated substrate
TXF Primer 20kg bucket 50m2 - 60m2  
TXF Acrylic 25kg bucket 9m2 - 10m2  
MonoFlexBase TXF Roll 50m2 (1m x 50m)  

TOTAL SYSTEM THICKNESS:

3 - 5mm to bond insulation + thickness of insulating component + 6mm base coats + 2mm for TXF acrylic finish.

For example a system using 90mm EPS would total approximately 100mm - 110mm in thickness.

The above information is supplied as a guide only; material usage and thickness is completely dependent on specific substrate type and condition.

Timber and steel frame

In timber/steel frame and SIPS type construction where the insulation is achieved prior to the external render coating the flexible MonoTherm TXF system components are installed over the enclosing render carrier board to provide a weatherproof decorative finish.

MonoFlexBase TXF is applied as a base coat in preparation for TXF Primer and the TXF Acrylic finish layer.

MonoMesh TXF is imbedded into the entire MonoFlexBase TXF layer whilst wet.

Mesh beads are installed to encapsulate the base coats and give definition to the finished product.

The battening configuration onto which the render carrier board is fixed may differ between board manufacturers and should be confirmed by them to ensure that specific product installation guidelines are met.

Click to view examples of external render carrier boards.

The following build up detail shows a typical MonoTherm TXF installation onto render carrier board and is provided as guidance only.

Build up guidance

MonoFlexBase TXF is installed over render board
MonoMesh TXF is imbedded within MonoFlexBase TXF layer
TXF Primer is applied over MonoFlexBase TXF when dry
TXF Acrylic is applied to finish

MATERIAL COVERAGE GUIDANCE

MonoFlex TXF 25kg bag 2.5m2 - 3m2 Base coating over render board
TXF Primer 20kg bucket 50m2 - 60m2  
TXF Acrylic 25kg bucket 9m2 - 10m2  
MonoFlexBase TXF Roll 50m2 (1m x 50m)  

TOTAL SYSTEM THICKNESS:

6mm of MonoFlexBase TXF + 2mm of TXF Acrylic + thickness of render carrier board.

For example a system using a 12mm render carrier board would total approximately 20mm in thickness.

The above information is supplied as a guide only; material usage and thickness is completely dependent on specific substrate type and condition.

Direct onto masonry

In some instances masonry panels may be present which do not require insulating however these areas need be rendered in the same finish as the surrounding insulated surfaces.

MonoFlexBase TXF is applied as a base coat in preparation for TXF Primer and the TXF Acrylic finish layer.

MonoMesh TXF is imbedded into the entire MonoFlexBase TXF layer whilst wet.

10mm beads are installed to encapsulate the base coats and give definition to the finished product.

The following build up detail shows a typical MonoTherm TXF acrylic installation onto masonry and is provided as guidance only.

Build up guidance

MonoFlexBase TXF is installed over masonry
MonoMesh TXF is imbedded within MonoFlexBase TXF layer
TXF Primer is applied over MonoFlexBase TXF when dry
TXF Acrylic is applied to finish

MATERIAL COVERAGE GUIDANCE

MonoFlex TXF 25kg bag 1.5m2 - 2m2 Base coating over masonry
TXF Primer 20kg bucket 50m2 - 60m2  
TXF Acrylic 25kg bucket 9m2 - 10m2  
MonoFlexBase TXF Roll 50m2 (1m x 50m)  

TOTAL SYSTEM THICKNESS: 12mm

The above information is supplied as a guide only; material usage and thickness is completely dependent on specific substrate type and condition.


Further information on Beads and Mesh

SYSTEM GUARANTEES

A 10 year system guarantee is supplied with the materials covering the system components when installed.

If you would like to receive a turnkey supply and install quotation for this system guaranteeing the highest standard of finish is achieved at site with a comprehensive 10 year warranty covering all system components and the workmanship throughout the installation process please call
0844 272 1467 or simply mail your enquiry to [email protected]

Standard Colours

The TXF Acrylic system is available in the following standard colours, TXF Primer and TXF Acrylic are not stock items and are generally mixed to order

Prices, availability and lead times are advised at point of order

TXF WHITE
TXF OFF WHITE
TXF IVORY
TXF CREAM
TXF LIGHT GREY
TXF SAND
TXF BEIGE

 

 

The above colour tiles are photographs of the actual MonoTherm TXF Acrylic finish material however the colour of the samples will appear slightly different when viewed from screen to screen / device to device

Finish options

The MonoTherm TXF system is finished with TXF Acrylic.

TXF Acrylic is a flexible through colour lightly textured decorative layer with a thickness of between 1mm and 2mm.

The nature of the material components and manufacturing process means that a greater depth is colour is achieved in comparison to sand and cement based alternatives.

TXF Acrylic finish

TXF Acrylic finish

The TXF Acrylic finish is achieved by working the applied material with a suitable trowel to create a smooth and consistent decorative texture.

Examples of TXF Acrylic finish

 

IMPORTANT NOTE:

The installation of MonoTherm TXF Acrylic finish should be considered as specialist and should be undertaken by experienced and where possible approved contractors.

It is advised that references and examples of previous projects showing the particular finish type you require are requested of the contractor prior to appointment.

TECHNICAL DATA SHEETS

TXF Acrylic 1.5mm
MonoFlexBase TXF
TXF Primer
MonoMesh TXF